Owner: User #71467

Cytolysis-1h HG v3.1.6 Delivery

HG v3.1.6 was delivered for Cytolysis on 1/12/16 for SUP720.  Testing scope will include ACE, SMITE and Tunnel.

CONOP will be:

• Hop through 3 flux nodes - 1 internet, 1 osmo subnet, 1 admin mgmt subnet - and IACInternational Access Code attack VLANVirtual Local Area Network 1 IP of target - XXX.XXX.X.XXX (TOPWAY-NET[CN])
• Trigger port will be UDPUser Datagram Protocol 161, host to impersonate will be explicitly set to a host not on VLANVirtual Local Area Network 10 or VLANVirtual Local Area Network 2
• Establish CTCounter Terrorism session over HTTPSHypertext Transfer Protocol Secure back through flux node 4
• Use ACEApplication Control Engine (Module) commands to verify state of the device
• Use socket get_arp_survey_data and output of "show ip nat trans" to survey traffic from VLANVirtual Local Area Network 19
• SMITE hosts on target customer network - VLANVirtual Local Area Network 19
• Use Tunnel to appear as if Operator is on VLANVirtual Local Area Network other than VLANVirtual Local Area Network 19 or VLANVirtual Local Area Network 2, and from there, nmap VLANVirtual Local Area Network 19.

Testing Summary

• Note in test report that module 2 is in state PwrDown and should be verified before proceeding
• Trigger packets that go through the target due to HG trigger sequence mis match will be caught and logged by outbound customer ACLs potentially - we will trigger to IP of device on port UDPUser Datagram Protocol 161
• Comms packets are SSLv3 - need to consider if this is noticeable on this network
• Hardware difference between test device and target - daughter card on 4 port 10G line card.  This hardware difference has been accepted.
• 5 sec CPU spikes to 55-65% during IACInternational Access Code attack, spike to 27% during HG install
• HG Consumes ~3.5M of Memory, visible in output out show mem

Testing Notes

1. Install
   -Memory at start of test:
   cytolysis-1#show mem
   Head Total(b) Used(b) Free(b) Lowest(b) Largest(b)
   Processor 453ACAF0 381990160 101796608 280193552 276504440 218810732
   I/O 8000000 67108864 13902404 53206460 53130184 53130428

   -attacked with IACInternational Access Code via flux
   -CPU hit a peak of 56% during IACInternational Access Code attack
   -Uploaded HG - show mem after install
   cytolysis-1#show mem
   Head Total(b) Used(b) Free(b) Lowest(b) Largest(b)
   Processor 453ACAF0 381990160 105273148 276717012 275964416 216779752
   I/O 8000000 67108864 13902404 53206460 53130184 53130428

   CPU hit one peak of 15% during install
   Used an interpacket delay of .1 for remote
   
   -Seeds traffic has been running
   -Established CTCounter Terrorism session impersonating XXX.XXX.X.XX (TOPWAY-NET[CN])
   -success! confirmed that XXX.XXX.X.XX (TOPWAY-NET[CN]) can still browse
   [XXX.XXX.X.XX (TOPWAY-NET[CN])]> packet get_assist_threshold_status
   [Success]
   Maximum Packets Per Second: 1500
   Number of Packets Counted Per Sample: 3000
   Highest Observed Packets Per Second: 173
   Number of Overflows Since Settings Last Changed: 0
   Time of Last Overflow: --
   ************ Success ************
   [packet get_assist_threshold_status]
   -no log messages or snmp traps observed, cpu normal
   *will want to impersonate a host that is not very busy, since an assist will be laid down for that host
   cytolysis-1#show ip cef XXX.XXX.X.XX (TOPWAY-NET[CN])
   XXX.XXX.X.XX (TOPWAY-NET[CN])/32
   receive
   cytolysis-1#
   -Quit the CTCounter Terrorism session and confirmed that after about 10 seconds, the RAA dropped:
   cytolysis-1#show ip cef XXX.XXX.X.XX (TOPWAY-NET[CN])
   XXX.XXX.X.XX (TOPWAY-NET[CN])/32
   attached to Vlan3
   cytolysis-1#

2. Uninstall
   

   -Re-established CTCounter Terrorism session, this time impersonating XXX.XXX.X.XX (TOPWAY-NET[CN]). No seeds currently running on that host.
   -Entered device uninstall-hg -mp -f to uninstall HG
   -no syslog or snmp trap observed
   -CPU from device after uninstall
   cytolysis-1# show proc cpu hist

   
   22222 44444 1111144444
   100
   90
   80
   70
   60
   50
   40
   30
   20
   10
   0....5....1....1....2....2....3....3....4....4....5....5....
   0 5 0 5 0 5 0 5 0 5
   CPU% per second (last 60 seconds)

   1 1 1 1 1 1 1
   0565955565466568566596566691570777976644965686666586545555
   100
   90
   80
   70
   60
   50
   40
   30
   20 * * *
   10 ************************************** ************* ****
   0....5....1....1....2....2....3....3....4....4....5....5....
   0 5 0 5 0 5 0 5 0 5
   CPU% per minute (last 60 minutes)
   * = maximum CPU% # = average CPU%

   521121211212212111212222211242112111211112122
   606719379081263898081510099121890987289981916
   100
   90
   80
   70
   60 *
   50 *
   40 * *
   30 * * * *
   20 *********************************************
   10 *********************************************
   0....5....1....1....2....2....3....3....4....4....5....5....6....6....7.
   0 5 0 5 0 5 0 5 0 5 0 5 0
   CPU% per hour (last 72 hours)
   * = maximum CPU% # = average CPU%

   cytolysis-1#
   cytolysis-1#show mem
   Head Total(b) Used(b) Free(b) Lowest(b) Largest(b)
   Processor 453ACAF0 381990160 101863176 280126984 275964416 218810732
   I/O 8000000 67108864 13902404 53206460 53130184 53130428
   
   RAA for impsonated host from CTCounter Terrorism session has dropped
   
   cytolysis-1#show ip cef XXX.XXX.X.XX (TOPWAY-NET[CN])
   XXX.XXX.X.XX (TOPWAY-NET[CN])/32
   attached to Vlan3
   cytolysis-1#

3. Modularity

   -Reloaded DUTDevice Under Test to start with a clean device
   -Flux nodes up, Seeds running on VLANVirtual Local Area Network 19
   -IAC attacked and uploaded HG
   -Established CTCounter Terrorism connection with XXX.XXX.X.XX (TOPWAY-NET[CN]) as impersonated host, no punch-throughs of traffic to impersonated host
   -Confirmed that impersonated host is still able to browse, did not observe any syslogs or traps sent by DUT
   -Stop/Start/Restarted ACEApplication Control Engine (Module) module - verified functionality after each start
   -Testing FB modularity and functionality with smite. Started up Victim3 VMVirtual Machine and web browsed with no rules active and saw the following print:
   
   Jan 19 19:03:08.193 C6506: %SEC-6-IPACCESSLOGP: list Core-Net-filter-in denied tcp X.X.X.XX (LVLT-GOGL-8-8-8[US])(80) (Vlan2 0015.fa80.efbf) -> 10.11.0.13(2213), 1 packetC
   - Added a rule for SMITE and saw the following
   cytolysis-1#show ip cef 10.11.0.13
   10.11.0.13/32
   attached to Vlan19
   cytolysis-1#
   Jan 19 19:09:02.877 C6506: %SEC-6-IPACCESSLOGP: list Core-Net-filter-in denied tcp X.X.X.XX (LVLT-GOGL-8-8-8[US])(80) (Vlan2 0015.fa80.efbf) -> 10.11.0.13(2213), 6 packets
   -successfully SMITE'd 3 more times with no prints
   -restarting FB
   -no rules active, browsed from victim, cleared cache and went to all 3 web servers 10x, no prints
   -activated SMITE rule and ran 7 times - then saw the following prints:

   Jan 19 20:02:55.049 C6506: %SEC-6-IPACCESSLOGP: list Customer-2-filter-in denied tcp XXX.XXX.X.XX (TOPWAY-NET[CN])(1041) (Vlan19 0050.5688.c5e6) -> X.X.X.XX (LVLT-GOGL-8-8-8[US])(7777), 1 packet
   Jan 19 20:08:04.769 C6506: %SEC-6-IPACCESSLOGP: list Customer-2-filter-in denied tcp XXX.XXX.X.XX (TOPWAY-NET[CN])(1041) (Vlan19 0050.5688.c5e6) -> X.X.X.XX (LVLT-GOGL-8-8-8[US])(7777), 7 packets
   Jan 19 20:09:04.801 C6506: %SEC-6-IPACCESSLOGP: list Core-Net-filter-in denied udp 10.9.8.22(137) (Vlan2 0021.d80d.cfc1) -> XXX.XXX.X.XX (TOPWAY-NET[CN])(137), 3 packets
   Jan 19 20:13:04.929 C6506: %SEC-6-IPACCESSLOGP: list Customer-2-filter-in denied tcp XXX.XXX.X.XX (TOPWAY-NET[CN])(1041) (Vlan19 0050.5688.c5e6) -> X.X.X.XX (LVLT-GOGL-8-8-8[US])(7777), 2 packets
   Jan 19 20:18:05.093 C6506: %SEC-6-IPACCESSLOGP: list Customer-2-filter-in denied tcp XXX.XXX.X.XX (TOPWAY-NET[CN])(1041) (Vlan19 0050.5688.c5e6) -> X.X.X.XX (LVLT-GOGL-8-8-8[US])(7777), 3 packetsC

4. Testing SMITE
   
   1. Starting over with Debian 8.2.  Installed ICON on TR, setup flux, cleaned DUT
   2. Restarted Victim 3 - web browsed 15 times to all three web servers and observed no prints
   3. Web browsed directly to iframe url 15 times and observed no prints
   4. Attacked with IACInternational Access Code and uploaded HG from new ICON 8.2 VMVirtual Machine - impersonating XXX.XXX.X.XX (TOPWAY-NET[CN])
   5. Restarted victim 3.  web browsed 15 times to all three web servers - no prints observed
   6. Web browsed directly to iframe url 15 times in a row - after the 10th try, observed the following:
      

      cytolysis-1#
      Jan 20 00:39:05.284 C6506: %SEC-6-IPACCESSLOGP: list Customer-2-filter-in denied tcp XXX.XXX.X.XX (TOPWAY-NET[CN])(1132) (Vlan19 0050.5688.c5e6) -> X.X.X.XX (LVLT-GOGL-8-8-8[US])(7777), 1 packet

   7. cytolysis-1#show access-list Customer-2-filter-in
      Extended IP access list Customer-2-filter-in
      10 permit tcp 10.11.0.0 0.0.0.255 host XXX.XXX.X.XX (TOPWAY-NET[CN]) eq 123
      20 permit udp 10.11.0.0 0.0.0.255 host XXX.XXX.X.XX (TOPWAY-NET[CN]) eq ntp
      30 permit icmp any host 10.11.0.1 (5870 matches)
      40 deny ip any 10.11.0.0 0.0.0.255 log-input
      50 permit icmp any host XXX.XXX.X.XX (TOPWAY-NET[CN])
      60 permit icmp any host XXX.XXX.X.XXX (TOPWAY-NET[CN])
      70 permit icmp any host XXX.XXX.X.XX (TOPWAY-NET[CN])
      80 permit icmp any host XXX.XXX.X.XXX (TOPWAY-NET[CN])
      90 deny ip any host XXX.XXX.X.XX (TOPWAY-NET[CN]) log-input
      100 deny ip any XXX.XXX.X.XX (TOPWAY-NET[CN]) 0.0.0.31 log-input
      110 deny ip any host XXX.XXX.X.XX (TOPWAY-NET[CN]) log-input
      120 deny ip any host XXX.XXX.X.XXX (TOPWAY-NET[CN]) log-input
      130 permit tcp 10.11.0.0 0.0.0.255 any eq smtp log-input
      140 permit tcp 10.11.0.0 0.0.0.255 any eq 135 log-input
      150 permit tcp 10.11.0.0 0.0.0.255 any eq 137 log-input
      160 permit tcp 10.11.0.0 0.0.0.255 any eq 139 log-input
      170 permit ip 10.11.0.0 0.0.0.255 any (22022 matches)
      180 deny ip any any log-input (1 match)
      cytolysis-1#

5. Characterization of print observed while browsing to windex server
   1. Collecting VLANVirtual Local Area Network 19 packet capture during print message
   2. set logging interval and threshold on DUTDevice Under Test so that logs will be seen immediately
   3. Set up span port for vlan 2 and vlan 19 on DUTDevice Under Test and collecting on the DC from g1/1
   4. Stopped the seeds traffic from cust2 to minimize output in wireshark
   5. Ran manual browses from target client to iframe url - took about ten tries, but I got the print and saved off the information that xetron had requested.
   6. Wiping HG, reload DUT, reload target.  Going to confirm once more that I really never get this print without HG by trying more times.
   7. Performed 30 browses to iframe url and no print.  Also browsed at least 30 times to other three web servers, no print
   8. Added HG, still no seeds, no CTCounter Terrorism session.  Repeating step g.  Observed print on the 24th iteration:

      Jan 22 00:22:01.499 C6506: %SEC-6-IPACCESSLOGP: list Customer-2-filter-in denied tcp XXX.XXX.X.XX (TOPWAY-NET[CN])(1262) (Vlan19 0050.5688.c5e6) -> X.X.X.XX (LVLT-GOGL-8-8-8[US])(7777), 1 packet

   9. Going to see if this occurs more during SMITE rule

   10. Established CTCounter Terrorism session and created smite rule:
       

       mitm create http_iframe 10.11.0.13 255.255.255.255 0 0 X.X.X.XX (LVLT-GOGL-8-8-8[US]) 255.255.255.255 80 80 "http://X.X.X.XX (LVLT-GOGL-8-8-8[US]):8888/?promo_code=1Z45RDJ" -bk -bc -en

   11. Observed prints with SMITE rule active as well at about the same rate

   12. Uninstalled and rebooted DUT
   13. Installed original version of delivery 3.1.5.
   14. Also working in installing newest version of windex in TR
   15. Was able to browse to iframe url 30 times from client wiht v3.1.5 and saw no prints.  however overnight, i had left the browser window open and windex session connected and at 4am, the router did log some messages:

   16. Jan 22 04:42:37.120 C6506: %SEC-6-IPACCESSLOGP: list Customer-2-filter-in denied tcp XXX.XXX.X.XX (TOPWAY-NET[CN])(1122) (Vlan19 0050.5688.c5e6) -> X.X.X.XX (LVLT-GOGL-8-8-8[US])(7777), 1 packet
       Jan 22 04:42:37.120 C6506: %SEC-6-IPACCESSLOGP: list Customer-2-filter-in denied tcp XXX.XXX.X.XX (TOPWAY-NET[CN])(1122) (Vlan19 0050.5688.c5e6) -> X.X.X.XX (LVLT-GOGL-8-8-8[US])(7777), 1 packet
       Jan 22 04:42:50.120 C6506: %SEC-6-IPACCESSLOGP: list Core-Net-filter-in denied udp 10.9.8.22(137) (Vlan2 0021.d80d.cfc1) -> XXX.XXX.X.XX (TOPWAY-NET[CN])(137), 1 packet
       Jan 22 04:42:51.636 C6506: %SEC-6-IPACCESSLOGP: list Core-Net-filter-in denied udp 10.9.8.22(137) (Vlan2 0021.d80d.cfc1) -> XXX.XXX.X.XX (TOPWAY-NET[CN])(137), 1 packet

   17. After attempting another 30 times without HG, I did reproduce the error message without HG.  This may just be a Windex/IOS NATNetwork Address Translation issue.  Hopefully this issue will be resolved in the newer version of Windex.
6. Testing Modularity
   1. Reloaded DUT
   2. CPU spike to 66% during IACInternational Access Code attack, 27% duing IACInternational Access Code install, 11% duing CTCounter Terrorism session establishment
   3. Already tested FB and ACEApplication Control Engine (Module) in previous test 3
   4. Testing Tunnel - Note that Tunnel module is not started by default.  Operator will have to start Tunnel module with "module start CovertTunnel.mod" command
   5. Started tunnel mod.  Then stopped it with module stop Tunnel.  Repeated three more times.
   6. Was unable to restart it at first, but after enough time passed and i entered ilm refresh, it did restart successfully.  no syslogs or traps observed, no impact to CPU.