Vault7: CIA Hacking Tools Revealed
Navigation: » Latest version
Detailed Notes regarding Samsung F8000 Smart TV networking
SECRET // REL USA,UK
In developing a WiFi reconnect watchdog when TV enters Fake-Off mode, the following information was learned about how the TV is configured
Kernel Drivers
Two related kernel drivers
- cfg80211 – module shown as loaded by lsmod and as a kernel thread by ps
- ath6kl_usb – module shown as loaded by lsmod, depends on cfg80211, and shown as kernel thread by ps
Contents of /mtd_cmmlib/WIFI_LIB/QCA/WIFI_INIT_VERSION_INFO are:
WIFI:ATH6KL(3.5.2.14.0204)
Notable Files and Directories:
/etc/Scripts/wifi_restart.sh – calls /sbin/wifi_module_reset which is not yet fully understood
iwconfig and ifconfig utilities are present on the system
Network configuration parameters held in /mtd_rwarea/network/ directory
- network_Wired_info – holds configuration for eth0. configuration remains there even when wlan0 is the active interface
- network_type_info – set to "CurrentType=0" for wired, or "CurrentType=1" for wireless
- wpa_sta.conf – contains wireless configuration parameters for the wpa_supplicant. Stores (last used) WPA passphrase in plaintext regardless of which interface is active. Appears to be in standard wpa_supplicant configuration file format
- entropy.dat – probably used with wpa_supplicant
/mtd_cmmlib/WIFI_LIB/QCA/ directory
-
iw – standard linux utility for interfacing with system's wireless networking. Potentially useful commands:
- iw wlan0 info
- iw wlan0 scan
- iw wlan0 get_average_signal
-
wpa_client – client for wpa_supplicant. Potentially useful commands:
- wpa_cli help
- wpa_cli status
- wpa_cli ping
- wpa_cli list_networks
- wpa_cli reconfigure
- wpa_cli reassociate
-
wpa_cli reauthenticate
- wpa_cli reconnect
- wpa_cli enable_network 0
- wpa_supplicant – daemon that handles wireless & WPA functionality
Experiments with Network Configuration Transitions:
- Start: wireless connected, manually add IP to eth0 with ifconfig
- eth0 keeps IP while powered on and while in Fake-Off
- eth0 loses IP when TV powered back on
- Start: wireless connected, use SmartHub to switch to wired
- eth0 reconfigured using previously configured static IP address
- wlan0 interface loses IP address
- wpa_cli status => wpa_state=INACTIVE
- wpa_sta.conf retains previous wlan0 settings and WPA credentials
- wpa_cli list_networks => last network shown with ID = 0, but as "[DISABLED]"
- Not certain all commands are required, but was able to re-active wlan0 with the following command sequence (this did not work in Fake-Off), but may if allowed to let the system settle more:
- wpa_cli reconfigure (wpa_state changed to DISCONNECTED)
- wpa_cli reassociate (wpa_state changed to INACTIVE)
- wpa_cli enable_network 0
- wpa_cli reconnect (wpa_state changed to COMPLETED, no IP)
- wpa_cli reassociate (wpa_state stays COMPLETED, no IP)
- udhcpc -i wlan0 -t 5 -T 5 -b (assigns IP to wlan0 interface and responds to pings)
- Start: wireless connected, manually add IP to eth0 with ifconfig, enter Fake-Off
- eth0 stays active with manually assigned IP (very useful for inspecting the system when in Fake-Off)
- wlan0 interface deleted (shown with ifconfig -a)
- wpa_supplicant continues to run in the background
- udhcpc no longer running (it has been killed)
- wpa_cli status => wpa_state=DISCONNECTED
- wpa_cli list_networks => ID = 0 with flags of "[DISABLED]"
- Could not find a sequence of ifconfig wlan0 up, wpa_cli enable_network 0, wpa_cli reconnect, wpa_cli reassociate, or wpa_cli reauthenticate that would bring up wlan0 into the needed wpa_state=CONNECTED. wpa_state=4WAY_HANDSHAKE was common.
- A process that did work was to kill/restart wpa_supplicant, and kill/restart udhcpc
- An observation that was not fully verified – it seemed that when entering Fake-Off, the wlan0 interface is disabled twice. Once right-away, and a second time 1-3 minutes later. This was observed when manually reseting wlan0 immediately after entering Fake-Off. Although it initially worked, the fix didn't stick as it seemed that something came along and disabled it again. After reseting it a second time, the interface appeared to stay up for a long period of time. Further diagnosis was not done since the solution should periodically check and reset.
- Start: wireless connected, use SmartHub to disconnect from wireless (also not connected to wired)
- wpa_cli status => wpa_state=INACTIVE
- wlan0 retains IP address and displayed by ifconfig
SECRET // REL USA,UK
You may also want to use visual panels to communicate related information, tips or things users need to be aware of.
Related articles
Related articles appear here based on the labels you select. Click to edit the macro and add or change labels.
('contentbylabel' missing)